X360Run1.1 (Slim+ Trinity) Glitcher Board Instruction

 

 

 

 

Ⅰ.The theory of X360Run Glitcher Board:

The X360Run send out a confirm width of pulse to XBOX360 slim machine. For different type XBOX360 slim machine have different type pulse time point and width.

Ⅱ.The X360Run Glitcher Board and trimming switch:

 

 
 

Product

 
   

 

 

 

Ⅲ.Configuration and trimming description:

The user must choose a different configuration options according to the different type XBOX360 slim machine.
The user can use the factory default setting of the X360Run Glitcher board.the user can use the trimmability switch to get a better time pulse,and this change will make XBOX360 machine achieve the best effective. Please choice default setting in the following three table,other setting only for test by user choice。Please use "Corona Mode 1" for Corona machine of Toshiba NandFlash on board and produced after Nov. 2013(need change the Windbond memory chip first)。 The Corona Mode2 for test by user choice。 The Compatible and function of Corona X360run Yellow-Board Mode same as X360Run Yellow Board。 X360Run Glitcher board have four type switch and trimming

adjustable setting:
(S: short the jumper pad , O:open the jumper pad)

1. The XBOX360 slim machine type setting

 

 

 

 

 

According to the different type XBOX360 machine , set the according M0,M1,M2 jumper pad with S or O follow this table. The value of capacitors about CD and CO must set correct too . the factory default value is Corona

Mode

1:SSO.

2. Pulse time delay trimming setting

 

 

 

 

 

 

The pulse time can be adjust to forward(forth:-1~-3) or backward(back:+1~+4) on the basis of the standard value. According to the different type XBOX360 machine, set the according D0,D1,D2 jumper pad with S or O follow this table. the factory default value is Corona Mode 1/X360Run Yellow-Board Corona
Mode:SSS(+1).

3. Pulse width trimming setting

 

 

 

 

 

The pulse width can be adjust to forward(forth:-1~-3) or backward (back:+1~+4) on the basis of the standard value. According to the different type XBOX360 machine, set the according W0,W1,W2 jumper pad with S or O follow this table. the factory default value is Corona Mode 1/X360Run Yellow-Board Corona
Mode:SSO(+2).

4. The adjustment of resistance and capacitance in the pulse signal output :

The D pin of X360Run Glitcher board is pulse signal output, can reduce the pulse signal strength by series resistance, the factory default value is 8.2Ώ. The D pin of X360Run Glitcher board is pulse signal output, can
produce an effect on launch XBOX360 slim machine succeed by shunt-wound differences value of Monolithic capacitance, the factory default value is CD=330pf(Corona),CD=220pf(Trinity9.6A) or CD=150pf(Trinity10.83A)
The length of two pins about CD capacitance don't cut to short(The length of CD capacitance about 1.5cm-1.7cm). Attention!: if replace Monolithic capacitance,must weld the new Monolithic capacitance complete before launch XBOX360 slim machine again.

5.Wire Install:
X360Run Glitcher board have SIX wire to be connected,them are:
1. Power Wire: VDD,
2. Ground Wire: GND,
3. I2C_SCL(E),
4. I2C_SDA(F),
5. POST_OUT(C),
6. CPU_RST(D)

①For Corona and Trinity 9.6A:
The 1—4 Wire direct connect to Glitcher board,about 10cm.The 5-6 Wire direct connect to Glitcher board,about 4cm to 7cm.can adjustment the length of 5-6 Wire in 4cm to 7cm carefully,then get the best effect.

②For Trinity 10.83A:
The 1—4 Wire direct connect to Glitcher board,about 10cm.The 5 Wire direct connect to Glitcher board,about 4cm to 7cm.can adjustment the length of 5 Wire in 4cm to 7cm carefully,then get the best effect. The 6 Wire direct connect to Glitcher board,about 4cm to 15cm(12cm is typical value).can adjustment the length of 6 Wire in 4cm to 15cm carefully,then get the best effect.

Attention!:

After modify the Xbox360 Trinity 10.83A machine,Must open and close
10 times to 20 times to check Whether or not Red-led on panel is Lights
up.if Red-led is Lights up,Can connect D point to GND point on X360Run
PCB Board with a 10K-20K metal-wire Resistor.

Ⅳ.The weld of changed XBOX360 slim machine

1. Corona-V1, Corona-V2

 

 

 

 

 

2. Corona-V3, Corona-V4, Corona-V5,Corona-V6

 

 

 

 

3. TRINITY

 

 

 

 

Ⅴ. Debug and install

 
 

 

 

"CPU_C"to"C" wire ;
"CPU_D"to"D" wire ;


The shunt-wound Monolithic capacitance CD [330pf(Corona) or 220pf(Trinity)],one pin weld to C1 point, another pin weld to a point between D point and C2 point.


The length of two pins about CD capacitance don't cut to short.